Encore E 3 Manuale Utente
Navigare online o scaricare Manuale Utente per Dispositivi elettronici per motoveicoli Encore E 3. Quick Start E3 Install Manual Manuale Utente
- Pagina / 2
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
:
QUICK START INSTALLATION GUIDE
If you are not proficient in the installation of this product or would
like a full version of the installation manual, Please visit our web
site @ www.encoreautomotivesystems.com
FOR PROFESSIONAL INSTALLATION ONLY!
RED / WHITE: PARKING LIGHT RELAY INPUT
WHITE: PARKING LIGHT OUTPUT
BLACK : MAIN SYSTEMS GROUND
BROWN : POSITIVE SIREN OUTPUT
RED : FUSED 12 VOLT (+) BATTERY POWER
Encore
E‐3
TRANSMITTER PROGRAMMING:
Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter
memory is exceeded, the security system will start deleting transmitters from memory in
chronological order.
1. Turn the Ignition 'switch ‘OFF/ON’ 4 TIMES and stay in ON position.
“Within 15 seconds”.
2. Push the Valet switch 4 times and hold it on the 4th push until a long chirp is heard. Then
release the valet switch. You are now in the Transmitter programming mode.
3. Press and hold any button of the transmitter until the siren responds with a confirming chirp,
indicating the signal has been stored into memory.
4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3 for
each transmitter.
Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. 3 long chirps & 3 parking light
flashes will confirm exit.
Main Power Connector
8 - Pin Accessory Connector
- GRAY WIRE / CHANNEL 3 NEGATIVE TRUNK OUTPUT
- ORANGE :STARTER INTERRUPT O/P RELAY REQUIRED
- YELLOW / IGNITION INPUT (+)
- GREEN / (-) DOOR TRIGGER INPUT
- BLUE / (-) INSTANT TRIGGER INPUT ( HOOD, TRUNK)
- VIOLET / (+) DOOR TRIGGER INPUT
- WHITE / DOME LIGHT (OR CH#4 O/P) RELAY REQUIRED
- BROWN/ WHITE / (-) HORN OUTPUT.
SECURITY FEATURE “A” PROGRAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 3 times (holding in on the 3rd push) until one long chirp is heard. Then
release the valet switch. You are now in the Alarm feature “A” programming mode.
3. Press and release the transmitter button corresponding to the feature you want to program.
a. The siren chirps and LED pause will indicate the current setting.
b. The factory default settings is always [1] LED flash, [1] chirp.
4 Depress the transmitter button to change the feature. Simply keep re-depressing the
transmitter button until the system advances to your desired setting.
Press the transmitter button corresponding to the feature you want to program.
Press
Transmitt
er
Button
One Chirp /
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulses
Three Chirps /
LED three
pulses
Four Chirps /
LED four
pulses
1
Active arming
Passive arming
without passive
door locking
Passive arming
with passive
door locking.
2
Automatic Rearm
off
Automatic Rearm
on
SECURITY FEATURE “B” PROGRAMMING:
Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
Push the Valet switch 4 times (holding in on the 4
th
push) until one long chirp is heard
then release the valet switch. You are now in the Alarm feature “B” programming
mode.
Press and release the transmitter button corresponding to the feature you want to
program.
Press
Transmitter
Button
One Chirp /
LED one
pulse
Factory
Default
Setting
Two Chirps /
LED two pulses
Three Chirps /
LED three
pulses
Four Chirps
/ LED four
pulses
1
Pathway
illumination
feature “off”
Parking light
turns “on” for 30-
second upon an
unlock signal
Parking light
turns “on” for 30-
second upon an
unlock signal &
10-second upon
a lock signal.
2
Ignition
controlled
door locks &
unlocks
Ignition
controlled door
locks only
Ignition
controlled door
unlocks only
Without
ignition
controlled
door locks
& unlocks
3
0.8-second
Door lock
pulses.
3.5-second Door
lock pulse.
Double pulse
unlock
Comfort
feature
4
3
r
d
Channel
(Trunk)
output
3
r
d
Channel
Latch output
Gray wire = Two
step door unlock
output
5 +
Button =
Silent
Arm/Disarm
Button = 4
th
Channel Aux.
6. +
Horn chirp
Duration
Standard
Horn chirp
Duration
50 mS
Horn chirp
Duration
30 mS
Horn chirp
duration
10 mS
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps will confirm
exit
3
Instant Door
Ajar error
chirp
45 seconds
delay Door Ajar
error chirp.
4
All
Confirmation
chirps On
Siren
Confirmation
chirp on only
Horn
Confirmation
chirp on only
All
Confirmation
chirps off
+
white wire =
Dome light
output
white wire = 4
th
channel pulse
white wire
=4
th
channel
latched
6 +
Lock/Arm &
Unlock/Disarm
Confirmation
Chirps
Lock/Arm
Confirmation
Chirp Only
7.
+
ALARM with
Keyless Entry
Keyless Entry
ONLY
8. +
Car Jacking
feature Off
Car Jacking
feature On
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps will confirm
exit.
Shock Sensor Adjustment:
1 Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2 Push the Valet switch 5 times and hold in on the 5th push. When a long
chirp is heard, release the valet switch. You are now in the Alarm feature
‘III’ programming mode.
3 Press the transmitter button corresponding to the feature you want to
program.
Press
Transmitter
Button
1
Shock Sensor Program Mode
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps will
confirm exit
ADJUST AND TEST THE SENSITIVITY LEVEL OF THE SHOCK SENSOR
1. Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 5 times holding in on the 5th push. a long chirp will be
heard. Release the valet switch. You are now in the Alarm feature ‘Shock
Sensor’ programming mode.
3. Press and hold
button for 2 seconds. One long siren chirp will indicate the
unit is ready to accept adjustments of the shock sensor.
4. Press
button on the transmitter once. This will decrease sensitivity level
by one. Each time the button is pushed and a decrease is made the
siren/horn chirp will respond with [1] chirp. Two chirps indicate the minimum
sensitivity. Warn away & full trigger will be deleted when minimum sensitivity
is selected
5. Press
button on the transmitter once. This will increase sensitivity level by
one. Each time an increase is made the siren/horn chirp will respond with [1]
chirp. Two chirps indicate the maximum sensitivity.
6. Hit the bumper or strong metal part of the vehicle to test the threshold level of
the sensor.
a). Activate the warn-away (first stage the shock sensor), the siren will
emit a short chirp.
b). Activate the full alarm (second stage the shock sensor), the siren will emit a
long chirp.
7. When you are satisfied with the setting, press the
button to lock in the
adjustment. One long siren chirp will indicate the unit has locked in the
adjustment.
Note: If 30 seconds of inactivity expires or you turn ON the ignition during of
above steps, the unit will exit the program mode and return to the disarmed
mode. Three long chirps will confirm exit.
FOR AUTHORIZED DEALER TECHNICAL SUPPORT,
PLEASE CALL Toll Free :(855) GO-ENCORE : 8:00 am
TO 5:00 pm PST.
1
2
Sommario
Pagina 1 - BROWN : POSITIVE SIREN OUTPUT
: QUICK START INSTALLATION GUIDE If you are not proficient in the installation of this pro
Pagina 2 - TRANSMITTER OPERATION
QUICK START USERS GUIDE If you do not understand any part of this quick start users manual and would like the complete version, Please visit our
Più documenti per Dispositivi elettronici per motoveicoli Encore E 3
Encore E 3 Manuale Utente
(10 pagine)
Encore E 3 Manuale di Installazione
(13 pagine)
Prodotti e manuali riguardandi Dispositivi elettronici per motoveicoli Encore E 3
(10 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.124 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale